Custom Gate & Access-Control Enclosures
Gate and access-control enclosures hold a keypad, reader, or intercom where a driver reaches it at a vehicle gate, and open for service behind it. K-Display cuts each faceplate to your device model.
Gate pedestals, cabinets, and device housings we build
We build gate and access-control enclosures as the metalwork at a vehicle gate: pedestals with a post on a base plate, control cabinets with hinged doors, and keypad, reader, and intercom housings with removable faceplates. Faceplates, housings, and device plates start as flat blanks we cut and form in aluminum, carbon steel, galvanized steel, galvanneal, or stainless steel, and the post and cabinet seams are welded in aluminum, carbon steel, or stainless steel. Parts leave bare, powder coated, or assembled with hinges and latches installed.
The housings and control boxes that mount on a door operator are door operator enclosures.
The faceplate lifts off the pedestal head, so a new device model changes the faceplate and leaves the post as it is. Only that plate carries the device's opening and attachment holes.
Gate and access-control parts we make
- Control cabinets
- Bodies and hinged doors with component mounts and cable-entry holes.
- Keypad, reader, and intercom housings
- Formed housings with removable faceplates, each carrying its device opening and attachment holes.
- Pedestals
- A post on a base plate with a device housing on top, with holes for the anchor pattern and conduit.
- Internal device plates
- Removable plates and brackets that hold the devices inside the cabinet or pedestal head.
What the field does to the enclosure
- Device geometry
- A device fits its faceplate only when the opening, attachment holes, and rear clearance match that model. A plate laid out for a similar model leaves gaps.
- Field service
- Replacing a component means opening the door in place. A door that meets the post or a wall never opens fully, so swing and hinge side decide whether a technician reaches the part.
- Weather and the NEMA type
- An outdoor cabinet takes rain at every seam and entry. The NEMA type you name sets the gasket land, closure, and entry hardware, and a seam that misses its gasket land lets the rain in.
- Edges and welds
- Coating thins on sharp edges and weld beads. On an outdoor post and faceplate those spots are where rust starts.
From flat blank to coated pedestal
A pedestal post has to stand square on its base plate, so the weld sequence is set to hold it there as the joint cools.
Laser cut, then form
We laser cut the faceplate openings, panels, and base plates flat, then form the bodies and doors.
Weld, dress, and fit hardware
We weld the post to its base plate and the cabinet seams, dress the welds and cut edges, and install hinges and latches.
Coat and assemble
We powder coat the parts, then hang the doors and seat the faceplates and device plates.
Connect the pedestal to the site
The cable route and anchor pattern share a small area at the pedestal base. Keep the incoming conduit within the post’s base opening, with room outside the post for a socket to reach each anchor nut. The cutaway shows how these two spaces sit alongside each other.
Check the base detail against the approved site layout before fabrication. Where a base cover is used, its movement and installation sequence need to leave the anchors accessible for tightening before the cover is lowered into place.
The central opening carries the conduit while the anchors need tool space outside the post. Raising the base cover exposes that fastening space, making cover movement part of the installation sequence.
What to send for a gate or access-control enclosure quote
- Device models and cutout drawings
- Model numbers with attachment patterns and rear clearance.
- Cabinet or pedestal model
- STEP or DXF plus a PDF, with installed height, door swing, and anchor pattern.
- Environment and NEMA type
- Where the pedestal or cabinet stands and the NEMA type your design names.
- Material and finish
- Alloy and thickness, powder product, and color.
- Hardware and quantity
- Hinge and latch part numbers, quantity, and delivery date.