Custom Kiosk Enclosures
A kiosk enclosure presents the screen and payment device to the public and opens behind them for service. K-Display fabricates the cabinets, bezels, and device plates for kiosk integrators, in carbon steel, stainless steel, or aluminum.
Kiosk enclosures we build
K-Display builds the cabinet that presents a screen and its devices to the public: a welded body and base, a bezel with an opening for each device, mounting plates inside, and service doors behind. The metal is carbon steel, stainless steel, or aluminum, supplied bare or powder coated, with hinges and latches installed and graphics silk-screened or applied to the face.
The cabinet holds the screen, payment device, printer, and cabling of self-order, self-checkout, and check-in kiosks. Cabinets that carry stock in trays and dispensing modules are vending enclosures.
The public uses the screen and payment device from the front, and a technician reaches the electronics from the side. With the two approaches on separate faces, a service call leaves the front closed.
Kiosk enclosure parts we make
- Cabinet bodies and bases
- Formed and welded housings and bases sized to the kiosk footprint and its mounting.
- Bezels and device panels
- Laser-cut openings for the screen, scanner, printer, and payment device.
- Internal mounting parts
- Plates, trays, and brackets that hold the electronics and peripherals, with self-clinching hardware pressed in for their fasteners.
- Service doors and covers
- Side and rear doors and covers that open onto the printer, paper roll, and cable runs.
Screens, peripherals, and the space behind them
- Device cutouts and rear space
- A device seats through a cutout sized to its bezel lip and clamps at the rear, so the front opening and the plate behind it have to be placed together. A cutout sized to the visible face alone leaves a device that will not seat.
- Public approach
- The accessibility standard you name (ADA, for example) gives reach ranges for device height and setback from the front edge. A payment device set too high or too deep falls outside them.
- Vents and cable paths
- The screen and its computer give off heat that has to leave the cabinet, and their cables have to pass through it. Vent slots and cable passages share the panels that carry the devices, so a plate that blocks a vent traps the heat behind the screen.
- Graphics against the openings
- Graphics sit on the finished face and are located from the device openings. A bezel edge, hinge, or latch that lands on the artwork covers it.
Openings cut to land after the bend
One shop cuts, forms, and fits the cabinet, so each opening is placed from the formed bezel and lands on its device once the bend is made.
Cut the bezel and plates
We laser cut the bezel openings, mounting plates, and vent slots in the flat blank, then form the bezel and the body.
Weld the body, press in hardware
We weld the body and base and press self-clinching nuts and studs into the plates and doors.
Mask, coat, fit, and mark
We mask the hardware threads and powder coat the cabinet, or leave the metal bare, then fit the hinges and latches and silk-screen or apply the graphics to the finished face.
Make the paper roll easy to replace
A service door can open fully while the printer’s own cover still hits the cabinet. In this representative layout, the printer stays on its mount as the cover opens and the roll lifts out through the side opening.
Allow space for the full replacement roll, not just the empty core. Following the selected printer’s loading sequence through to closing its cover reveals where a shelf, door return, or cable route would interrupt the task before the enclosure layout is fixed.
The printer remains mounted while its cover opens and the roll lifts out. The cabinet opening needs room for the full replacement roll and that movement; an open service door alone does not establish usable access.
What to send for a kiosk enclosure quote
- Device drawings
- Screen, payment device, and printer part numbers, CAD, and cutout templates.
- Reach and approach
- Device heights, the accessibility standard, and the direction the public approaches from.
- Service layout
- Door swing, consumable changes, cable routes, and vent locations.
- Material and site
- Carbon steel, stainless steel, or aluminum, the footprint and anchorage, and whether the kiosk stands indoors or outdoors.
- Finish and artwork
- Powder color and texture, artwork files, and where each graphic sits.
- Quantity and schedule
- Kiosks per order, variants by device configuration, and ship dates.